Intel Edison Breakout Board Spezifikationen PDF herunterladen (Seite 30)

Shield pin configuration

11.6 Configure IO18/IO19 for I

C connectivity

To configure IO18 and IO19 for I

C connectivity, do the following:

1. Refer to Table 2 for the GPIO numbers. According to Table 2, the GPIO numbers for IO18 and IO19 are 28

and 27, respectively.

2. According to Table 4, GPIO 204 must be set to 1 to select GPIO/I

C, and GPIO 28 pin-mux must be set to

‘mode1’ to select I

C for IO18.

3. According to Table 4, GPIO 205 must be set to 1 to select GPIO/I2C, and GPIO 27 pin-mux must be set to

‘mode1’ to select I

C for IO19.

4. GPIO 14 and GPIO 165 are also connected to the I

C signals, and should be configured as high-

impedance inputs when I

C is in use on these pins, to prevent them driving a signal on the I

C bus.

5. According to Table 7, GPIO 236 must be set to 0 to disable the output direction for GPIO 14, and GPIO 237

must be set to 0 to disable the output direction for GPIO 165.

6. According to Table 7, GPIO 212 and 213 must be set as high-impedance inputs to disable the pullup

resistors for IO18 and IO19, respectively.

7. According to Table 6, the TRI_STATE_ALL signal is controlled by GPIO 214.

After you have gathered all of this information, enter the following commands in Linux:

# echo 28 > /sys/class/gpio/export

# echo 27 > /sys/class/gpio/export

# echo 204 > /sys/class/gpio/export

# echo 205 > /sys/class/gpio/export

# echo 236 > /sys/class/gpio/export

# echo 237 > /sys/class/gpio/export

# echo 14 > /sys/class/gpio/export

# echo 165 > /sys/class/gpio/export

# echo 212 > /sys/class/gpio/export

# echo 213 > /sys/class/gpio/export

# echo 214 > /sys/class/gpio/export

# echo high > /sys/class/gpio/gpio214/direction

# echo high > /sys/class/gpio/gpio204/direction

# echo high > /sys/class/gpio/gpio205/direction

# echo in > /sys/class/gpio/gpio14/direction

# echo in > /sys/class/gpio/gpio165/direction

# echo low > /sys/class/gpio/gpio236/direction

# echo low > /sys/class/gpio/gpio237/direction

# echo in > /sys/class/gpio/gpio212/direction

# echo in > /sys/class/gpio/gpio213/direction

# echo mode1 > /sys/kernel/debug/gpio_debug/gpio28/current_pinmux

# echo mode1 > /sys/kernel/debug/gpio_debug/gpio27/current_pinmux

# echo low > /sys/class/gpio/gpio214/direction

You should be able to use IO18 and IO19 for I

C communication.

Intel® Edison Kit for Arduino*

Hardware Guide December 2014

30 Document Number: 331191-004

1 2 ... 25 26 27 28 29 30 31 32

Kommentare zu diesen Handbüchern

ThomasSleno 13 Feb 2024 | 13:02:49

Hello.

LamaRek 23 Feb 2024 | 09:36:11

I want to show you one exclusive program called (BTC PROFIT SEARCH AND MINING PHRASES), which can make you a rich man! This program searches for Bitcoin wallets with a balance, and tries to find a secret phrase for them to get full access to the lost wallet! Run the program and wait, and in order to increase your chances, install the program on all computers available to you, at work, with your friends, with your relatives, you can also ask your classmates to use the program, so your c

NerryPongE 24 Feb 2024 | 05:20:03

Hello from Happykiddi.

Intel Edison Breakout Board Spezifikationen Seite 30

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Entwicklungsboards Intel Edison Breakout Board